Keurig espresso makers are a well-liked technique to make a fast and simple cup of espresso. Nonetheless, in case your Keurig begins to malfunction, you could have to take it aside to troubleshoot the issue. Taking aside a Keurig can appear to be a frightening activity, however it’s truly fairly easy with the correct instruments and directions.
Earlier than you begin taking aside your Keurig, make sure you unplug it from the facility outlet. Additionally, you will want to assemble a number of instruments, together with a Phillips head screwdriver, a flathead screwdriver, and a pair of pliers. After getting your instruments, you may comply with the steps beneath to take aside your Keurig:
First, take away the water reservoir. The water reservoir is situated on the again of the Keurig. To take away it, merely raise it up and pull it out. Subsequent, take away the drip tray. The drip tray is situated underneath the brew head. To take away it, merely pull it out. Lastly, take away the brew head. The brew head is situated on the high of the Keurig. To take away it, flip the locking lever to the unlock place and pull the brew head up and out.
Disassembling the Outer Casing
Earlier than you may entry the internal workings of your Keurig, you might want to disassemble the outer casing. This can be a comparatively easy course of, however it’s vital to comply with the steps fastidiously to keep away from damaging your espresso maker.
1. Take away the highest cowl
Begin by eradicating the highest cowl of the Keurig. On most fashions, the highest cowl is held in place by two screws situated behind the machine. Use a Phillips head screwdriver to take away the screws, then raise the highest cowl off the machine.
As soon as the highest cowl is eliminated, you will note the water reservoir and the brewing chamber. The water reservoir is situated on the left aspect of the machine, and the brewing chamber is situated on the correct aspect.
To take away the water reservoir, merely raise it up and out of the machine. To take away the brewing chamber, press down on the discharge button situated on the highest of the chamber, then raise the chamber out of the machine.
2. Take away the aspect panels
The subsequent step is to take away the aspect panels of the Keurig. On most fashions, the aspect panels are held in place by two screws situated on the high and backside of every panel. Use a Phillips head screwdriver to take away the screws, then raise the aspect panels off the machine.
As soon as the aspect panels are eliminated, you will note the inner elements of the Keurig. These elements embody the heating aspect, the pump, and the management board.
3. Take away the underside cowl
The ultimate step is to take away the underside cowl of the Keurig. On most fashions, the underside cowl is held in place by 4 screws situated on the corners of the duvet. Use a Phillips head screwdriver to take away the screws, then raise the underside cowl off the machine.
As soon as the underside cowl is eliminated, you’ll have entry to the entire inside elements of the Keurig. Now you can start troubleshooting or repairing your espresso maker.
Eradicating the Water Reservoir
Eradicating the water reservoir is easy and could be accomplished in just some steps. Make it possible for the espresso maker is turned off and unplugged earlier than beginning.
1. Find the water reservoir launch button.
The water reservoir launch button is often situated on the again or aspect of the espresso maker. It’s usually a small, black button.
2. Press the water reservoir launch button and pull the reservoir straight up.
After getting situated the water reservoir launch button, press it and pull the reservoir straight up. The reservoir ought to come out simply. If you’re having bother eradicating the reservoir, strive wiggling it gently back and forth.
The reservoir has quite a lot of inside elements that will dislodge throughout the elimination or filling course of. Here is a visible information to assist establish these elements:
| Part | Description |
|---|---|
| Water Degree Indicator | A float that rises and falls with the water degree. |
| Water Degree Sensor | A sensor that detects the water degree and shuts off the espresso maker when the reservoir is empty. |
| Pump | A pump that circulates the water via the espresso maker. |
3. As soon as the reservoir has been eliminated, you may clear it with heat, soapy water.
Be sure to rinse the reservoir totally and permit it to dry utterly earlier than changing it.
Disconnecting the Electrical Wires
As soon as you’ve got eliminated the outer casing, it is time to disconnect {the electrical} wires. These wires are what energy the Keurig, so it is vital to watch out when dealing with them.
Step 1: Find the Electrical Wires
{The electrical} wires are situated on the underside of the Keurig. They’re often held in place by a plastic clip.
Step 2: Take away the Plastic Clip
Use a screwdriver or your fingernails to take away the plastic clip. This can launch {the electrical} wires.
Step 3: Disconnect the Electrical Wires
As soon as {the electrical} wires are launched, you may disconnect them. To do that, merely pull the wires aside.
| Wire Colour | Connection |
|---|---|
| Black | Widespread |
| Pink | Line |
| White | Impartial |
Eradicating the Plunger and Needles
To take away the plunger and needles, first take away the highest cowl of the Keurig. Then, find the plunger meeting. It’s a cylindrical-shaped half that’s situated within the middle of the machine. Grip the plunger meeting and pull it straight up. This can take away the plunger and needles from the machine.
As soon as the plunger and needles have been eliminated, you may clear them. To wash the plunger, merely wipe it down with a humid material. To wash the needles, use a mushy brush to take away any espresso grounds or particles. As soon as the plunger and needles are clear, you may reassemble the Keurig.
Cleansing the Plunger Meeting
| Step | Description |
|---|---|
| 1 | Take away the highest cowl of the Keurig. |
| 2 | Find the plunger meeting. It’s a cylindrical-shaped half that’s situated within the middle of the machine. |
| 3 | Grip the plunger meeting and pull it straight up. This can take away the plunger and needles from the machine. |
| 4 | Wipe down the plunger with a humid material. |
| 5 | Use a mushy brush to take away any espresso grounds or particles from the needles. |
| 6 | Reassemble the Keurig. |
Accessing the Inside Parts
To entry the inner elements of the Keurig machine, you will need to fastidiously disassemble the outside housing. Here is a step-by-step information to take action:
1. Unplug the Machine
Start by unplugging the Keurig machine from the facility outlet to make sure your security.
2. Find the Screws
Subsequent, find the screws that maintain the outside housing collectively. On most Keurig fashions, these screws are discovered on the again of the machine or beneath the drip tray.
3. Take away the Exterior Housing
Use a screwdriver to take away the screws, after which gently raise the outside housing off the machine. Watch out to not injury any wires or inside elements.
4. Find the Screws Holding the Chassis
Inside the outside housing, you’ll find the chassis, which holds the inner elements in place. Find the screws that maintain the chassis in place, that are usually discovered on the perimeters or backside.
5. Take away the Chassis
Use a screwdriver to take away the screws, after which fastidiously raise the chassis out of the machine. Take care to not pull any wires or injury any elements.
6. Troubleshooting
Generally throughout disassembly, you could encounter some frequent points. Here is a troubleshooting information that can assist you resolve them:
| Concern | Answer |
|---|---|
| Stripped screw | Use a rubber band or small piece of paper between the screwdriver and the screw to achieve further grip. |
| Caught elements | Gently faucet on the element with a rubber mallet or use a skinny, flat instrument to pry it aside. |
| Broken or disconnected wires | Examine the wires for any injury or disconnection. If mandatory, reconnect or restore the wires utilizing wire connectors or electrical tape. |
Disconnecting the Management Board
As soon as you’ve got eliminated the highest cowl and entrance panel, it is time to disconnect the management board. This can be a delicate step, so take your time and watch out to not injury any of the elements.
Step 1: Establish the Management Board
The management board is often situated within the middle of the machine, behind the entrance panel. It is a inexperienced circuit board with quite a lot of wires and connectors connected to it.
Step 2: Disconnect the Wires
Use a pair of needle-nose pliers to disconnect the wires from the management board. There are two sorts of wires: energy wires and knowledge wires. Energy wires are often thicker and have a black or pink insulation. Information wires are thinner and have a yellow or white insulation.
Step 3: Take away the Connectors
As soon as the wires are disconnected, you may take away the connectors from the management board. Connectors are small plastic plugs that join the wires to the board. To take away a connector, gently pry it up with a small screwdriver.
Step 4: Carry the Management Board
As soon as the connectors are eliminated, you may raise the management board up and out of the machine. Watch out to not injury any of the elements on the board.
Step 5: Place the Management Board in a Protected Location
As soon as the management board is eliminated, place it in a protected location the place it will not get broken. You’ll be able to put it in a plastic bag or wrap it in a towel.
Step 6: Double-Examine Your Work
Earlier than you progress on to the following step, double-check your work to ensure that the entire wires and connectors are disconnected from the management board. This can assist to forestall any injury to the machine once you reassemble it.
Step 7: Troubleshooting Suggestions
If you happen to’re having bother disconnecting the management board, listed here are a number of troubleshooting ideas:
| Downside | Answer |
|---|---|
| I am unable to disconnect the wires from the management board. | Just be sure you’re utilizing the proper kind of pliers. Needle-nose pliers are the most effective kind of pliers for this job. |
| I am unable to take away the connectors from the management board. | Attempt utilizing a small screwdriver to softly pry the connectors up. Watch out to not injury the connectors or the board. |
| I unintentionally broken the management board. | If you happen to unintentionally broken the management board, you will have to interchange it. You should purchase a alternative management board from the producer of your Keurig machine. |
Eradicating the Move Sensor
The move sensor is a small, plastic element situated within the water line of your Keurig. It helps to find out how a lot water is pumped into the brew chamber. To take away the move sensor, comply with these steps:
1. Unplug the Keurig
Earlier than you start, ensure that the Keurig is unplugged from {the electrical} outlet.
2. Find the move sensor
The move sensor is situated on the underside of the Keurig, close to the water line.
3. Take away the screws
There are two screws that maintain the move sensor in place. Take away these screws utilizing a Phillips head screwdriver.
4. Disconnect the wires
As soon as the screws are eliminated, you will have to disconnect the 2 wires which are linked to the move sensor.
5. Take away the move sensor
As soon as the wires are disconnected, you may take away the move sensor by gently pulling it out of the water line.
6. Examine the move sensor
After getting eliminated the move sensor, take a second to examine it for any injury. If the move sensor is broken, it can must be changed.
7. Clear the move sensor
If the move sensor isn’t broken, you may clear it by rinsing it with water.
8. Reinstall the move sensor
To reinstall the move sensor, merely reverse the steps that you simply took to take away it. Remember to tighten the screws securely, however don’t overtighten them.
Disassembling the Drip Tray
1. **Find the drip tray latch:** The drip tray is held in place by a latch situated on the underside of the machine.
2. **Press the latch:** Firmly press down on the latch to launch it.
3. **Pull out the drip tray:** As soon as the latch is launched, gently pull out the drip tray.
4. **Take away the cup assist:** The cup assist is a small plastic piece that sits contained in the drip tray. Grasp the cup assist and pull it straight as much as take away it.
5. **Clear the drip tray and cup assist:** Use a humid material to wipe down the drip tray and cup assist. If there’s any espresso residue, use a light detergent to wash it off.
6. **Reassemble the drip tray:** Place the cup assist again into the drip tray, then insert the drip tray again into the machine.
7. **Shut the latch:** Push down on the latch to safe the drip tray in place.
Eradicating the Drip Tray Float
8. **Find the drip tray float:** The drip tray float is a small plastic ball that sits contained in the drip tray. It helps to detect when the drip tray is full.
9. **Take away the drip tray float:** To take away the drip tray float, gently push down on the float and pull it out of the drip tray. The float is held in place by a small magnet, so it could require somewhat power to take away it.
| Step | Motion |
|---|---|
| 1 | Find the drip tray latch. |
| 2 | Press the latch. |
| 3 | Pull out the drip tray. |
| 4 | Take away the cup assist. |
| 5 | Clear the drip tray and cup assist. |
| 6 | Reassemble the drip tray. |
| 7 | Shut the latch. |
| 8 | Find the drip tray float. |
| 9 | Take away the drip tray float. |
Cleansing and Reassembling the Parts
Now that the Keurig is disassembled, it is time to clear the elements. Use heat, soapy water and a mushy material to wipe down the entire detachable components. Take particular care to wash the needle and the water reservoir.
As soon as the elements are clear, it is time to reassemble the Keurig. Begin by inserting the water reservoir into the bottom of the machine. Then, exchange the drip tray and the Ok-Cup holder.
Subsequent, insert the needle into the highest of the machine. Make it possible for the needle is correctly aligned in order that it will possibly puncture the Ok-Cups.
Lastly, exchange the highest of the machine and plug within the Keurig. Your Keurig is now prepared to make use of!
Cleansing the Water Reservoir
The water reservoir is without doubt one of the most vital elements of your Keurig. It is vital to wash the water reservoir usually to forestall the buildup of mould and micro organism.
To wash the water reservoir, take away it from the Keurig and rinse it with heat water. Then, add a number of drops of dish cleaning soap to the water reservoir and swish it round. Lastly, rinse the water reservoir totally with heat water and exchange it within the Keurig.
Cleansing the Needle
The needle is one other vital element of your Keurig. It is vital to wash the needle usually to forestall it from clogging. Some keurig fashions have a detachable needle, whereas others don’t. To wash the needle, merely use a mushy material and gently wipe away any espresso grounds or different particles. In case your Keurig mannequin has a detachable needle, you may take away it and soak it in heat, soapy water for a couple of minutes. Then, rinse the needle totally with heat water and exchange it within the Keurig.
Cleansing the Ok-Cup Holder
The Ok-Cup holder is one other element of your Keurig that ought to be cleaned usually. To wash the Ok-Cup holder, merely take away it from the Keurig and rinse it with heat water. Then, use a mushy material to wipe away any espresso grounds or different particles. Lastly, exchange the Ok-Cup holder within the Keurig.
| Kind | Cleansing technique |
|---|---|
| Water reservoir | Rinse with heat water, add a number of drops of dish cleaning soap, swish round, rinse totally |
| Needle | Wipe with a mushy material, take away and soak in heat, soapy water (if detachable) |
| Ok-Cup holder | Rinse with heat water, wipe with a mushy material |
How To Take Aside A Keurig
Listed here are the steps on the way to take aside a Keurig:
- Unplug the Keurig and let it quiet down.
- Take away the water reservoir and drip tray.
- Flip the Keurig the wrong way up and take away the 4 screws that maintain the underside panel in place.
- Fastidiously raise the underside panel off of the Keurig.
- Find the 2 screws that maintain the heating aspect in place and take away them.
- Fastidiously raise the heating aspect out of the Keurig.
- Find the 2 screws that maintain the pump in place and take away them.
- Fastidiously raise the pump out of the Keurig.
- Find the 2 screws that maintain the management board in place and take away them.
- Fastidiously raise the management board out of the Keurig.
Individuals Additionally Ask About How To Take Aside A Keurig
How do I clear the within of my Keurig?
To wash the within of your Keurig, you will have to descale it. Descaling is the method of eradicating mineral buildup from the within of the Keurig. You’ll be able to descale your Keurig utilizing a descaling answer or vinegar.
How do I repair a Keurig that’s not brewing?
In case your Keurig isn’t brewing, there are some things you may examine:
- Make it possible for the Keurig is plugged in and turned on.
- Make it possible for there’s water within the water reservoir.
- Make it possible for the Ok-cup is correctly inserted into the Keurig.
- Make it possible for the needle within the Keurig isn’t clogged.
How do I exchange the water filter in my Keurig?
To switch the water filter in your Keurig, you will have to:
- Take away the water reservoir from the Keurig.
- Find the water filter within the backside of the water reservoir.
- Take away the previous water filter and insert the brand new water filter.
- Change the water reservoir within the Keurig.
