Microwave ovens are a standard kitchen equipment that can be utilized to prepare dinner, reheat, and defrost meals. They’re comparatively straightforward to make use of, however eradicating them from the wall could be a bit tougher. If you’re planning to maneuver or transform your kitchen, chances are you’ll have to take away your overhead microwave. Listed below are a number of recommendations on how you can do it safely and simply.
Earlier than you start, just be sure you have all the needed instruments and supplies. You have to a screwdriver, a wrench, and a pair of pliers. You may additionally want a ladder in case your microwave is mounted excessive on the wall. After getting gathered your instruments, you possibly can start the elimination course of. First, unplug the microwave from {the electrical} outlet. Then, take away the mounting screws which might be holding the microwave to the wall. As soon as the screws are eliminated, you possibly can rigorously carry the microwave off of the wall and set it apart.
As soon as the microwave is eliminated, you possibly can disconnect {the electrical} wires which might be related to it. Watch out to not injury the wires, as this might create a hearth hazard. As soon as the wires are disconnected, you possibly can take away the microwave fully. If you’re planning to maneuver the microwave to a brand new location, remember to pack it rigorously to keep away from injury. You may additionally need to take into account hiring knowledgeable that can assist you transfer the microwave, particularly if it’s a heavy mannequin.
Disconnecting the Energy Provide
### 1. Shut off the electrical energy to the microwave.
Earlier than you start any work, it’s essential to make sure your security by disconnecting the facility provide to the microwave. Find {the electrical} panel to your dwelling and flip the circuit breaker that corresponds to the microwave circuit to the “OFF” place. You may also unplug the microwave from {the electrical} outlet whether it is related to at least one.
### 2. Look ahead to the microwave to chill down.
As soon as the facility provide is disconnected, enable the microwave to chill down for a minimum of half-hour earlier than making an attempt to take away it. That is to stop any burns from residual warmth within the equipment.
### 3. Take away the mounting screws.
After the microwave has cooled, find the mounting screws that safe it to the wall or cupboard above it. These screws can often be discovered on the highest or backside of the microwave, relying on the mannequin. Use a screwdriver to take away these screws, however don’t take away the microwave from the wall or cupboard but.
### 4. Help the microwave whereas eradicating it.
With the mounting screws eliminated, you might be able to take away the microwave from its place. Get somebody that can assist you carry and help the microwave whilst you rigorously slide it out of the wall or cupboard. Be aware to not drop or injury the equipment throughout this course of.
Eradicating the Mounting Screws
As soon as the facility has been disconnected, you possibly can start eradicating the mounting screws. These screws are usually positioned on the high of the microwave, on both facet of the unit. They could be lined by plastic caps or covers, which you’ll be able to gently pry off with a flathead screwdriver.
Utilizing a Phillips head screwdriver, rigorously loosen the mounting screws by turning them counterclockwise. Don’t take away the screws fully at this level, because the microwave remains to be connected to the wall by {the electrical} twine and bracket.
As soon as the mounting screws are free, you possibly can gently pull the microwave ahead and away from the wall. Watch out to not pull too laborious, as chances are you’ll injury {the electrical} twine or bracket.
| Instrument Required | Steps |
|---|---|
| Flathead screwdriver | Pry off plastic caps or covers |
| Phillips head screwdriver | Loosen mounting screws |
| Gently pull microwave ahead | Detach from wall |
Unplugging the Wiring Harness
Unplugging the wiring harness is a vital step in eradicating an overhead microwave. It requires cautious consideration to element to make sure security and forestall injury to the equipment. Listed below are the steps concerned:
1. Flip Off Energy and Unplug the Microwave
Earlier than touching any electrical parts, make sure the microwave is disconnected from the facility provide. Find {the electrical} outlet and unplug the microwave from the wall. Don’t yank or pull on the twine, as this may increasingly injury the wiring.
2. Find and Entry the Junction Field
The junction field is a metallic enclosure that comprises {the electrical} connections for the microwave. It’s usually positioned inside the cupboard or behind the microwave itself. Entry the junction field by unscrewing the duvet or eradicating any bolts or screws holding it in place.
3. Unplug the Wiring Harness
After getting entry to the junction field, you will notice a bundle of wires related to the microwave’s wiring harness. Every wire is often recognized by a special coloration. To unplug the wiring harness, observe these steps rigorously:
- Establish Terminals: Find the terminals on the junction field the place the wires from the wiring harness are related. Terminals are usually labeled or color-coded.
- Loosen Screws: Utilizing a screwdriver, loosen the screws on the terminals to launch the wires from the wiring harness.
- Pull Wires: Gently pull every wire straight out of the terminal. Don’t pull on the wire itself, as this may increasingly injury the wire or the terminal.
- Disconnect Harness: As soon as all of the wires are disconnected, rigorously carry the wiring harness away from the junction field.
Confer with this desk for a extra detailed visible information to unplugging the wiring harness:
| Step | Description |
|---|---|
| 1 | Establish terminals and loosen screws. |
| 2 | Pull wires straight out of terminals. |
| 3 | Disconnect wiring harness from junction field. |
Eradicating the Trim Plate
The trim plate is the ornamental panel that covers the perimeters of the microwave oven and conceals its mounting screws. To take away the trim plate, observe these steps:
1. Unplug the microwave oven from {the electrical} outlet.
2. Find the screws that maintain the trim plate in place. They’re usually positioned on the highest and backside of the trim plate.
3. Take away the screws utilizing a screwdriver. Watch out to not drop the screws.
4. Gently pull the trim plate away from the microwave oven. It ought to come off simply.
5. If the trim plate is caught, chances are you’ll want to make use of a putty knife or a skinny, flat object to softly pry it free. Insert the putty knife or flat object between the trim plate and the microwave oven and thoroughly pry the trim plate away from the oven. Watch out to not injury the trim plate or the microwave oven.
As soon as the trim plate is eliminated, you should have entry to the mounting screws that maintain the microwave oven in place. Now you can proceed to the subsequent step of the elimination course of.
Disassembling the Microwave
PREPARATIONS
Earlier than disassembling the microwave, guarantee energy provide is minimize off, plug is faraway from socket, and the gadget is chilly.
REMOVING THE CABINET
Establish the mounting screws or bolts securing the microwave to the cupboard. Unscrew or unbolt them rigorously. Grip the microwave firmly, carry it straight up off the cupboard, and set it apart.
DISCONNECTING THE WIRING
Find the wiring harness connecting the microwave to the facility provide and cupboard. Disconnect the harness by unplugging the connectors or unscrewing the terminals. Label wires if needed for simpler reassembly.
REMOVING THE MOUNTING BRACKETS
Unfasten the mounting brackets attaching the microwave to the wall or ceiling. These could also be secured with screws or bolts; use applicable instruments to take away them.
DETACHING THE DOOR
Open the microwave door absolutely. Find the hinges connecting the door to the microwave physique. Unscrew or unbolt the hinges and thoroughly carry the door off the microwave.
ACCESSING THE INTERNAL COMPONENTS
As soon as the door is eliminated, you possibly can entry the inner parts of the microwave. These could embody the magnetron, waveguide, fan motor, and turntable motor. Deal with parts gently to keep away from injury.
ELECTRICAL COMPONENTS
MAGNETRON
The magnetron is a vacuum tube that generates microwaves. It’s positioned within the base of the microwave oven and is chargeable for heating the meals. The magnetron is a important part and may solely get replaced by a professional technician.
WAVEGUIDE
The waveguide is a metallic tube that carries microwaves from the magnetron to the cooking chamber. It is very important maintain the waveguide clear and freed from obstructions.
FAN MOTOR
The fan motor circulates air contained in the microwave oven to chill the parts and forestall overheating. The fan motor is often positioned behind the microwave oven.
TURNTABLE MOTOR
The turntable motor rotates the turntable contained in the microwave oven, making certain that meals is cooked evenly. The turntable motor is often positioned within the backside of the microwave oven.
Cleansing the Microwave
1. Unplug the microwave.
Earlier than you start cleansing, remember to unplug the microwave from {the electrical} outlet. This may forestall the microwave from by accident turning on while you’re cleansing it.
2. Take away the turntable and turntable ring.
The turntable and turntable ring might be eliminated by merely lifting them out of the microwave. Make sure to wash these things in sizzling, soapy water and dry them totally earlier than changing them.
3. Clear the inside of the microwave.
The inside of the microwave might be cleaned with a light detergent and water. Use a sponge or material to wipe down the inside surfaces, together with the door, the ceiling, and the edges. Make sure to rinse the inside totally with clear water and dry it with a clear material.
4. Clear the outside of the microwave.
The outside of the microwave might be cleaned with a light detergent and water. Use a sponge or material to wipe down the outside surfaces, together with the door, the edges, and the highest. Make sure to rinse the outside totally with clear water and dry it with a clear material.
5. Clear the door gasket.
The door gasket is a rubber seal that helps to maintain the microwave door closed. Over time, the door gasket can turn out to be soiled and greasy. Use a sponge or material to wipe down the door gasket with a light detergent and water. Make sure to rinse the door gasket totally with clear water and dry it with a clear material.
6. Clear the vent.
The vent is positioned on the highest or facet of the microwave. It’s used to exhaust air from the microwave. Over time, the vent can turn out to be clogged with mud and particles. Use a vacuum cleaner to wash the vent. Make sure to take away any mud or particles from the vent.
7. Clear the microwave filter.
The microwave filter is positioned behind the vent. It’s used to lure grease and smoke from the microwave. Over time, the microwave filter can turn out to be clogged with grease and smoke. It is very important clear the microwave filter repeatedly to make sure that the microwave is working correctly. To scrub the microwave filter, take away it from the microwave and wash it in sizzling, soapy water. Make sure to rinse the microwave filter totally with clear water and dry it totally earlier than changing it.
| Cleansing Job | Frequency |
|---|---|
| Clear the inside of the microwave | Month-to-month |
| Clear the outside of the microwave | Month-to-month |
| Clear the door gasket | Month-to-month |
| Clear the vent | Each 3 months |
| Clear the microwave filter | Each 6 months |
Reinstalling the Microwave
1. Flip off the facility to the microwave on the circuit breaker.
2. Take away the mounting screws that maintain the microwave to the cupboard.
3. Fastidiously carry the microwave off the mounting bracket.
4. Take away the facility twine from the outlet.
5. Take away the exhaust duct from the microwave.
6. If the microwave is vented outdoors, take away the vent cap from the outside wall.
7. Clear the mounting floor and the again of the microwave.
8. Apply a bead of caulk across the perimeter of the mounting floor. This may assist to seal the microwave and forestall drafts.
| Step | Motion |
|—|—|
| 1 | Flip off the facility to the microwave on the circuit breaker. |
| 2 | Take away the mounting screws that maintain the microwave to the cupboard. |
| 3 | Fastidiously carry the microwave off the mounting bracket. |
| 4 | Take away the facility twine from the outlet. |
| 5 | Take away the exhaust duct from the microwave. |
| 6 | If the microwave is vented outdoors, take away the vent cap from the outside wall. |
| 7 | Clear the mounting floor and the again of the microwave. |
| 8 | Apply a bead of caulk across the perimeter of the mounting floor. This may assist to seal the microwave and forestall drafts. |
9. Place the microwave on the mounting bracket and align the screw holes.
10. Insert the mounting screws and tighten them securely.
11. Join the facility twine to the outlet.
12. Set up the exhaust duct to the microwave.
13. If the microwave is vented outdoors, set up the vent cap on the outside wall.
14. Activate the facility to the microwave on the circuit breaker.
15. Take a look at the microwave to verify it’s working correctly.
Reconnecting the Energy Provide
Step 1: Unplug the Microwave.
Earlier than touching any wires, be sure that the microwave is totally disconnected from the facility supply. Find the facility twine and pull the plug from the wall outlet.
Step 2: Establish the Wires.
Inside {the electrical} field, you’ll find a number of wires related to the microwave. These wires will usually be black, white, and inexperienced (or naked copper) and are held along with wire nuts.
Step 3: Take away the Wire Nuts.
Fastidiously take away the wire nuts by twisting them counterclockwise. Be cautious to not injury the wires.
Step 4: Separate the Wires.
As soon as the wire nuts are eliminated, gently separate the black and white wires from one another. The inexperienced (or naked copper) wire is the bottom wire and may stay related.
Step 5: Join the New Microwave.
Align the wires from the brand new microwave with the corresponding wires from {the electrical} field. Twist the black wire from the brand new microwave with the black wire from the field, and do the identical for the white wires.
Step 6: Safe the Wire Nuts.
Place a brand new wire nut over every set of twisted wires and tighten it clockwise till cosy. Be sure that the wires are securely related.
Step 7: Take a look at the Wiring.
Earlier than reconnecting the facility, double-check your connections utilizing a multimeter to make sure correct continuity and no brief circuits.
Step 8: Reconnect the Energy.
Plug the microwave energy twine again into the wall outlet and activate the breaker or fuse to revive energy to the equipment.
Step 9: Take a look at the Microwave.
Press the facility button on the microwave to make sure that it’s functioning appropriately. If the microwave doesn’t activate or operates abnormally, repeat the above steps to verify for any free connections or wiring errors.
Testing the Microwave
Earlier than making an attempt to take away the microwave, it is essential to make sure it is turned off and unplugged from the facility supply. Comply with these steps to confirm the microwave’s standing:
1. Verify the Energy Change
Find the facility change on the microwave’s entrance or facet panel. Be sure that it is turned to the “Off” place.
2. Unplug the Microwave
Find {the electrical} outlet the place the microwave is plugged in. Firmly grasp the plug and pull it straight out of the outlet.
3. Look ahead to Capacitor to Discharge
After unplugging the microwave, enable a couple of minutes for the capacitor to discharge. This may forestall any electrical shock hazard.
4. Open the Microwave Door
As soon as the capacitor has discharged, open the microwave door to launch any remaining vitality.
5. Verify for Residual Warmth
Really feel the within and outdoors of the microwave to make sure it is fully cool. If it is nonetheless heat, wait longer earlier than continuing.
6. Visually Examine the Microwave
Study the microwave for any injury or free elements. Should you discover something uncommon, don’t try and take away it your self and phone a professional equipment restore technician.
7. Collect Crucial Instruments
You’ll seemingly want a Phillips head screwdriver and a flathead screwdriver to take away the microwave.
8. Put on Protecting Gear
Placed on security glasses and gloves to guard your self from sharp edges or electrical parts.
9. Disconnect Electrical Wires
As soon as the microwave is faraway from the wall, rigorously disconnect {the electrical} wires from the terminal block. Observe the place of every wire for reconnection later.
10. Take away the Mounting Bracket
Find the mounting bracket that secures the microwave to the wall. Utilizing the suitable screwdriver, take away the screws or bolts that maintain the bracket in place. Watch out to not drop the microwave when eradicating it from the bracket.
How To Take away A Overhead Microwave
Eradicating an overhead microwave could be a daunting job, however it’s positively potential to do it your self with the appropriate instruments and slightly little bit of know-how. Listed below are the steps on how you can do it:
- Flip off the facility to the microwave. This may be accomplished by unplugging it from the outlet or by turning off the breaker that controls the facility to the microwave.
- Take away the mounting screws. There are often 4 screws that maintain the microwave in place. These screws are positioned on the highest of the microwave, close to the again. Use a screwdriver to take away the screws.
- Fastidiously carry the microwave off of the wall. As soon as the screws are eliminated, you possibly can rigorously carry the microwave off of the wall. Make sure to help the burden of the microwave together with your different hand.
- Disconnect the wiring. As soon as the microwave is off of the wall, it’s essential disconnect the wiring. There are often two wires that join the microwave to the facility supply. Use a pair of pliers to disconnect the wires.
- Take away the microwave from the kitchen. As soon as the wiring is disconnected, you possibly can take away the microwave from the kitchen. Make sure to carry the microwave rigorously and keep away from bumping it into something.
Folks Additionally Ask About How To Take away A Overhead Microwave
How do I take away a microwave from a cupboard?
To take away a microwave from a cupboard, you will have to:
- Open the cupboard door.
- Find the screws which might be holding the microwave in place.
- Take away the screws.
- Fastidiously carry the microwave out of the cupboard.
How do I take away a microwave from a wall bracket?
To take away a microwave from a wall bracket, you will have to:
- Flip off the facility to the microwave.
- Take away the screws which might be holding the microwave to the wall bracket.
- Fastidiously carry the microwave off of the wall bracket.
- Disconnect the wiring from the microwave.
How do I take away a in-built microwave?
To take away a in-built microwave, you will have to:
- Flip off the facility to the microwave.
- Take away the trim across the microwave.
- Take away the screws which might be holding the microwave in place.
- Fastidiously carry the microwave out of the cupboard.
- Disconnect the wiring from the microwave.
