Putting in a Ring Stick Up Cam is a straightforward and efficient technique to improve your property safety. By following a couple of easy steps, you’ll be able to shortly and simply mount your digicam in an optimum location to watch your property and deter potential intruders. This information will give you complete directions on tips on how to mount your Ring Stick Up Cam, guaranteeing a safe and dependable set up.
Earlier than you start, collect the required instruments and supplies. You will want a screwdriver, a drill, a stage, a tape measure, and the mounting {hardware} included along with your Ring Stick Up Cam. Moreover, chances are you’ll want a ladder or step stool in case you are mounting the digicam in a excessive location. After you have gathered your supplies, select an appropriate location on your digicam. Contemplate components similar to the realm you need to monitor, the peak and angle of the digicam, and the supply of an influence supply.
After you have chosen a location, use a stage to make sure that the mounting floor is stage. Mark the screw holes on the floor utilizing a pencil or marker. Drill pilot holes on the marked places and insert the included screws. Align the Ring Stick Up Cam with the screws and slide it into place. Tighten the screws utilizing a screwdriver to safe the digicam. Make sure that the digicam is firmly hooked up to the floor and that it’s stage. Lastly, join the Ring Stick Up Cam to the Ring app in your smartphone or pill to finish the set up and start monitoring your property.
Deciding on the Optimum Mounting Location
Discovering the most effective mounting location on your Ring Stick Up Cam is essential to make sure optimum efficiency and effectiveness. Listed below are some key components to contemplate when selecting the mounting spot:
- Visibility: Make sure that the digicam has a transparent view of the realm you need to monitor. Keep away from obstructions like timber, shrubs, or fences that would block the digicam’s discipline of view.
- Top: Mount the digicam at a top that gives a wide-angle view, capturing each the bottom stage and the encompassing space. A top of 7-9 toes is usually advisable, although modify it primarily based in your particular necessities.
- Angle: Decide the angle at which you need to view the realm. Contemplate the situation of potential intruders, the course of motion, and the presence of blind spots. Angle the digicam accordingly to maximise protection and decrease blind areas.
- Energy supply: Make sure that the mounting location gives entry to an influence outlet or appropriate photo voltaic panel to maintain the digicam powered. If choosing solar energy, be certain the situation receives ample daylight all through the day.
- Safety: Select a mounting location that’s troublesome for unauthorized people to succeed in or tamper with. Think about using excessive mounting factors or hid areas to reinforce the digicam’s safety.
- Climate resistance: If mounting open air, choose a location that is protected against excessive climate circumstances similar to rain, snow, or direct daylight. Think about using a weatherproof enclosure to protect the digicam from the weather.
| Issue | Issues |
|---|---|
| Visibility | Unobstructed discipline of view, clear view of desired space |
| Top | 7-9 toes advisable, modify primarily based on necessities |
| Angle | Maximize protection, decrease blind spots |
| Energy Supply | Entry to energy outlet or photo voltaic panel |
| Safety | Tough to succeed in or tamper with |
| Climate Resistance | Protected against climate circumstances, weatherproof enclosure |
Gathering Important Mounting {Hardware}
1. Decide Your Mounting Floor
Earlier than you start, confirm the kind of floor you may be mounting your Ring Stick Up Cam on. Widespread surfaces embody partitions, ceilings, eaves, and soffits. The kind of floor will decide the {hardware} you want.
2. Select the Proper {Hardware}
Relying in your mounting floor, chances are you’ll want the next:
- Screws: Use the screws supplied along with your Ring Stick Up Cam for many surfaces. For particularly exhausting surfaces, think about using stainless-steel or hardened screws.
- Wall anchors: Use drywall anchors if mounting on drywall or plasterboard to supply a safe maintain. Select the suitable anchor dimension primarily based on the load of the digicam.
- Mounting screws: Use the supplied mounting screws to safe the digicam’s mounting bracket to the floor.
3. Collect Instruments
Along with the mounting {hardware}, you may additionally want the next instruments:
- Drill or driver: Use a drill or driver to create pilot holes and drive screws.
- Degree: Use a stage to make sure your Ring Stick Up Cam is mounted straight for optimum efficiency.
- Tape measure: Measure the gap between mounting factors for exact placement.
- Pencil: Mark the drilling places on the floor.
- Security glasses: Put on security glasses whereas drilling or driving screws to guard your eyes.
Getting ready the Mounting Floor
Selecting the Proper Location
* Choose a location that gives a transparent view of the specified monitoring space.
* Guarantee the situation is free from obstructions, similar to timber, fences, or buildings.
* Contemplate the peak at which the digicam will probably be mounted to keep away from tampering or blind spots.
Getting ready the Floor
* For drywall or wooden surfaces: Use a stud finder to find an appropriate stud for help.
* For concrete surfaces: Drill pilot holes and insert plastic anchors earlier than screwing within the mounting bracket.
* For glass or metallic surfaces: Make the most of double-sided tape or magnetic mounting choices to safe the bracket.
Leveling and Aligning the Bracket
* Use a stage to make sure the mounting bracket is stage.
* Regulate the angle of the bracket to realize the specified discipline of view.
* Mark the mounting holes with a pencil or pen earlier than drilling.
* Non-obligatory: Set up a silicone base underneath the bracket to forestall water ingress (advisable for out of doors installations).
Putting in the Baseplate
1. Select a mounting location: Choose a location with a transparent view of the realm you need to monitor and the place the digicam can obtain a powerful Wi-Fi sign.
2. Mark the mounting gap places: Use the included template or a pencil to mark the place the screws will go for the baseplate.
3. Drill pilot holes (optionally available): When you’re mounting the digicam on a tough floor like concrete or brick, drill small pilot holes on the marked places.
4. Safe the baseplate: Use the included screws and a screwdriver to connect the baseplate firmly to the floor. Make sure the baseplate is stage and aligned accurately with the specified digicam view.
Detailed Directions for Securing the Baseplate
* Use the right screws: The Ring Stick Up Cam comes with particular screws designed for various mounting surfaces. Make sure you use the suitable screws on your floor sort.
* Tighten the screws firmly: Use a screwdriver to tighten the screws securely, guaranteeing the baseplate is tightly hooked up. Nonetheless, keep away from overtightening to forestall harm.
* Verify for stage: Use a stage or the built-in bubble stage function on the baseplate to make sure it is mounted stage. This ensures the digicam may have a correct discipline of view when put in.
* Keep away from uneven surfaces: Make sure the baseplate is mounted on a flat and even floor to forestall the digicam from tilting or wobbling.
5. Push the digicam onto the baseplate: Align the digicam with the baseplate and push it down till it snaps into place.
Ideas:
*
- Use a drill bit barely smaller than the screw diameter for pilot holes.
- If mounting on a mushy floor like drywall, chances are you’ll use anchors to make sure a safe maintain.
- Think about using a water-resistant silicone sealant across the baseplate edges for added climate resistance.
Aligning and Attaching the Digicam
5. Aligning and attaching the digicam
As soon as the mounting bracket is securely fixed to the floor, you are able to align and connect the digicam. Here is a step-by-step information:
| Step | Description |
|---|---|
| 1. Take away the protecting movie | Take away the protecting movie masking the adhesive pads on the mounting bracket. |
| 2. Place the digicam | Align the digicam with the mounting bracket and gently press it into place. Make sure the screw gap on the backside of the digicam aligns with the screw gap on the mounting bracket. |
| 3. Tighten the screw | Find the screw included within the package deal and insert it into the screw holes on the digicam and mounting bracket. Use a screwdriver to tighten the screw till the digicam is securely fixed. |
| 4. Rotate the digicam | As soon as the digicam is hooked up, modify its place by rotating it till it faces the specified course. |
| 5. Regulate the angle | Utilizing your fingertips, gently push the digicam’s physique up or down to regulate the viewing angle. Make sure the digicam is positioned to seize the optimum view of the realm you propose to watch. |
Bear in mind to deal with the digicam with care through the alignment and attachment course of to keep away from damaging the gadget or its elements.
Inserting the Batteries
Elevate the rubber tab on the again of the digicam and insert the included batteries into the compartment. The proper orientation will probably be indicated contained in the compartment. Change the rubber tab when completed.
Tightening the Screws and Cables
Use a screwdriver to tighten the screws that safe the mounting bracket to the wall. Make sure that the screws are cosy however not overtightened.
Connecting the Energy Cable (Wired Possibility)
For Out of doors Use:
Join the facility plug to the facility port on the again of the digicam. Then, thread the facility cable by way of the outlet within the mounting bracket and safe it with the included pressure aid.
For Indoor Use:
Plug the facility cable into an indoor outlet. Then, thread the cable by way of the outlet within the mounting bracket and safe it with the included pressure aid.
Connecting to Wi-Fi
Obtain the Ring app and create an account. Observe the in-app directions to attach the digicam to your Wi-Fi community.
Positioning the Digicam
Regulate the digicam’s angle and place to seize the specified discipline of view. Use the stay view within the Ring app to assist with exact placement.
Connecting the Digicam to Energy
Ring Stick Up Cam requires a steady energy supply to perform correctly. There are two main methods to attach your digicam to energy:
1. Wired Connection:
- Determine an appropriate indoor or out of doors electrical outlet close to the specified digicam location.
- Join the supplied energy adapter to the digicam’s energy port.
- Plug the facility adapter into {the electrical} outlet.
2. Battery Energy:
- Take away the battery pack from the digicam.
- Insert the supplied lithium-ion battery into the pack.
- Reinsert the battery pack into the digicam.
Powering the Digicam with a Photo voltaic Panel
Ring additionally affords a photo voltaic panel accent to cost the digicam’s battery. This can be a nice possibility for places with ample daylight and a want to cut back wire muddle. To make use of the photo voltaic panel:
| Step | Description |
|---|---|
| 1 | Connect the photo voltaic panel to the digicam mount utilizing the screws supplied. |
| 2 | Place the photo voltaic panel in a location with direct daylight. |
| 3 | Make sure that the photo voltaic panel cable is related to the digicam’s energy port. |
Configuring the Digicam Settings
After you have efficiently mounted your Ring Stick Up Cam, it is time to configure the digicam settings to customise the digicam’s conduct and performance.
Wi-Fi Setup
Begin by connecting the digicam to your Wi-Fi community. Guarantee your Wi-Fi password is helpful and comply with the on-screen prompts within the Ring app to ascertain the connection.
Movement Detection Zones
Outline particular areas throughout the digicam’s discipline of view the place movement ought to set off alerts. Customise the scale and form of those zones to give attention to related areas and decrease false alerts.
Movement Sensitivity
Regulate the sensitivity of the digicam’s movement sensor to find out how simply it detects motion. Increased sensitivity settings will lead to extra frequent alerts, whereas decrease settings will cut back false alerts.
Night time Imaginative and prescient
Allow or disable evening imaginative and prescient to permit the digicam to seize footage in low-light circumstances. Select between “Greatest Video High quality” for sharper pictures with barely decreased evening imaginative and prescient vary or “Greatest Night time Imaginative and prescient” for enhanced evening imaginative and prescient efficiency.
Video Settings
Configure the video decision and body fee to find out the standard and smoothness of the captured footage. Increased decision settings will present clearer pictures however eat extra bandwidth.
Audio Settings
Allow or disable audio recording to seize sound alongside the video footage. Regulate the audio sensitivity to find out the quantity threshold that triggers alerts.
Privateness Zones
Create privateness zones throughout the digicam’s discipline of view the place movement is not going to set off alerts. This function permits you to exclude particular areas, similar to your neighbor’s property or a public sidewalk, from surveillance.
Recording Modes
Select between steady recording, motion-activated recording, or scheduled recording. Steady recording captures footage on a regular basis, whereas motion-activated recording solely data when movement is detected. Scheduled recording permits you to specify particular time intervals for recording.
Testing the Digicam’s Operation
As soon as you have put in your Ring Stick Up Cam, it is necessary to try it out to ensure it is working correctly.
-
Open the Ring app in your smartphone or pill.
The Ring app is obtainable totally free on the App Retailer and Google Play.
-
Faucet on the Gadgets tab.
It will present you a listing of all of the Ring gadgets that you’ve got related to your account.
-
Choose your Stick Up Cam.
It will open the Stay View display on your digicam.
-
Faucet on the microphone icon.
It will can help you discuss by way of your digicam’s speaker.
-
Converse into the microphone.
You need to hear your voice coming by way of the digicam’s speaker.
-
Faucet on the movement detection icon.
It will present you a listing of all of the movement occasions which have been recorded by your digicam.
-
Choose a movement occasion.
It will open the video playback display for the movement occasion.
-
Watch the video.
It will can help you see what triggered the movement occasion.
-
Take a look at the digicam’s evening imaginative and prescient.
To check the digicam’s evening imaginative and prescient, you have to to attend till it’s darkish exterior. As soon as it’s darkish, faucet on the evening imaginative and prescient icon within the Stay View display. It will activate the digicam’s evening imaginative and prescient mode. You need to now be capable of see at midnight.
Sustaining the Digicam’s Efficiency
Optimizing Digicam Placement
* Set up the digicam at an applicable top and angle for clear visibility.
* Select a location with minimal obstructions and keep away from direct daylight to forestall picture distortion.
Making certain Correct Energy Provide
* Use the supplied energy cable or join the digicam to a steady Wi-Fi community for steady operation.
* If utilizing batteries, exchange them frequently to keep away from interruptions.
Common Cleansing
* Wipe the digicam’s lens with a mushy fabric to take away mud and particles that may hinder the picture.
* Use a barely damp fabric to scrub the digicam’s exterior, avoiding harsh chemical compounds which will harm the end.
Firmware Updates
* Repeatedly examine for and set up firmware updates to make sure optimum digicam efficiency and safety.
Resetting the Digicam
* If the digicam experiences any points, carry out a manufacturing unit reset by holding down the setup button for 15 seconds.
* It will clear all settings and restore the digicam to its default configuration.
Troubleshooting Widespread Points
* Verify the Wi-Fi connection if the digicam is offline.
* Regulate the digicam’s sensitivity settings to reduce false triggers.
* Contact Ring help for help with any unresolved points.
Battery Conservation Ideas
* Disable movement detection for non-critical areas to increase battery life.
* Regulate the digicam’s decision and body fee to decrease energy consumption.
* Use an influence financial institution or photo voltaic panel to complement the digicam’s battery energy.
Digicam Upkeep Schedule
| Upkeep Process | Frequency |
|---|---|
| Clear Lens | Month-to-month |
| Verify Wi-Fi Connection | Weekly |
| Firmware Replace | As wanted |
| Manufacturing facility Reset | If experiencing points |
Learn how to Mount a Ring Stick Up Cam
The Ring Stick Up Cam is a flexible house safety digicam that may be mounted indoors or open air. It is easy to put in, and you may select from quite a lot of mounts to seek out the proper match on your house.
To mount your Ring Stick Up Cam, you have to the next:
- A Ring Stick Up Cam
- A appropriate mount (bought individually)
- A drill (if mounting the digicam open air)
- Screws (if mounting the digicam open air)
- A stage (optionally available)
After you have your entire supplies, you’ll be able to comply with these steps to mount your Ring Stick Up Cam:
1.
Select a location on your digicam. The most effective location on your digicam will rely upon the realm you need to monitor. Contemplate the peak of the digicam, the angle of the digicam, and the quantity of sunshine within the space.
2.
Connect the mount to the wall or ceiling. If you’re mounting the digicam open air, you have to to make use of a drill to create pilot holes for the screws. As soon as the pilot holes are created, insert the screws into the holes and tighten them till the mount is safe.
3.
Connect the digicam to the mount. Align the digicam with the mount and snap it into place. Ensure that the digicam is securely hooked up to the mount.
4.
Regulate the angle of the digicam. As soon as the digicam is hooked up to the mount, you’ll be able to modify the angle of the digicam to get the most effective view of the realm you need to monitor.
5.
Take a look at the digicam. As soon as the digicam is mounted and adjusted, check it to ensure it’s working correctly. Open the Ring app in your cellphone and comply with the directions to attach the digicam to your Wi-Fi community.
Folks additionally ask about Learn how to Mount Ring Stick Up Cam
How excessive ought to I mount my Ring Stick Up Cam?
The most effective top on your Ring Stick Up Cam will rely upon the realm you need to monitor. Nonetheless, rule of thumb is to mount the digicam at the least 7 toes excessive. It will assist to forestall folks from tampering with the digicam and also will offer you a greater view of the realm.
Can I mount my Ring Stick Up Cam the wrong way up?
Sure, you’ll be able to mount your Ring Stick Up Cam the wrong way up. Nonetheless, you have to to make use of the included wedge equipment to take action. The wedge equipment will assist to angle the digicam accurately so that you could get view of the realm you need to monitor.
Can I mount my Ring Stick Up Cam on a tree?
Sure, you’ll be able to mount your Ring Stick Up Cam on a tree. Nonetheless, you have to to make use of a tree mount equipment (bought individually) to take action. The tree mount equipment will assist to safe the digicam to the tree and also will defend the digicam from the weather.
