The Rolex watch is a luxurious timepiece that’s identified for its high quality and craftsmanship. Nevertheless, even the best watches require upkeep every so often, and one of the frequent upkeep duties is eradicating the again of the watch. This is usually a tough job, however it’s one that may be carried out at residence with the precise instruments and data.
Earlier than you start, you will need to collect the required instruments. You will want a small screwdriver, a case knife or butter knife, and a smooth fabric. You might also wish to use a pair of tweezers that can assist you take away the again of the watch. After getting your instruments, you may start the method of eradicating the again of the watch.
To take away the again of the watch, you have to to first find the small notch on the aspect of the case. This notch is often positioned close to the 6 o’clock place. After getting discovered the notch, you have to to insert the tip of the screwdriver into the notch and pry the again of the watch open. Watch out to not pry too onerous, as you don’t want to wreck the watch. As soon as the again of the watch is open, you have to to make use of the case knife or butter knife to take away the gasket. The gasket is a rubber ring that helps to seal the again of the watch and forestall water from coming into. As soon as the gasket has been eliminated, it is possible for you to to entry the motion of the watch.
Instruments and Preparation
To efficiently take away the again of a Rolex watch, you have to the next instruments and supplies:
Important Instruments:
| Instrument | Objective |
|---|---|
| Caseback removing device | 专门用于移除 Rolex 手表的表背。 |
| Crystal press | 在更换表镜时，可用来将表镜压入表壳。 |
| Spring bar device | 用于移除表带或表链上的弹簧杆。 |
| 镊子 | 用于取出微小的部件或垫圈。 |
| 手套 | 保护手表免受指纹和污垢影响。 |
可选工具：
| Instrument | Objective |
|---|---|
| 手表清洁液 | 清洁表壳和表背。 |
| 备用垫圈 | 如有必要，可更换表背垫圈。 |
| 除锈剂 | 去除表背和表壳上的锈迹。 |
| Case Kind | Rotation Path |
|---|---|
| Oyster Case | Counterclockwise |
| Snap-On Case | Counterclockwise |
| Screw-On Case | Clockwise |
Troubleshooting Widespread Points
Problem: The watch remains to be underneath guarantee.
If the watch remains to be underneath guarantee and you’re experiencing issues, you need to contact your nearest Rolex approved supplier. They may be capable of diagnose and restore the watch at no cost.
Problem: The watch isn’t underneath guarantee.
If the watch isn’t underneath guarantee, you should still be capable of get it repaired. You’ll be able to take it to a Rolex approved supplier or to a certified watchmaker. The price of the restore will differ relying on the problem.
Problem: I’ve misplaced the particular Rolex device.
When you have misplaced the particular Rolex device, you should purchase a alternative from a Rolex approved supplier. The price of the device is $15.
Problem: The case again remains to be caught.
If the case again remains to be caught after following the steps above, you might want to make use of a rubber mallet to faucet it gently. Watch out to not hit the case again too onerous, as you might injury the watch.
Problem: I’ve broken the watch.
When you have broken the watch whereas attempting to take away the again, you need to take it to a Rolex approved supplier for restore. The price of the restore will differ relying on the extent of the injury.
Problem: I’m not comfy eradicating the again of the watch myself.
In case you are not comfy eradicating the again of the watch your self, you may take it to a Rolex approved supplier or to a certified watchmaker. They may be capable of take away the again of the look ahead to you.
Reattaching the Caseback
7. Tightening the Caseback
Gently tighten the caseback onto the watch head utilizing a caseback wrench or spanner. It is essential to use gradual and even strain to forestall injury or overtightening.
Flip the wrench clockwise to regularly tighten the caseback till it is seated in opposition to the gasket. Keep away from extreme drive to forestall distortion or injury.
As soon as the caseback is securely tightened, recheck the gasket for correct seating and any indicators of injury. If the gasket is broken or improperly seated, it might compromise the watch’s water resistance.
| Strain | Time |
|---|---|
| Gentle-to-moderate | 5-10 seconds |
| Agency | 10-15 seconds |
| Cosy | 15-20 seconds |
The perfect tightness varies relying on the particular watch mannequin and its water resistance score. In case you’re uncertain concerning the acceptable strain, seek the advice of the producer’s tips or search skilled watch restore help.
Tightening the Caseback
After cleansing, it’s time to tighten the caseback onto the watch. This may be carried out by hand or utilizing a caseback press.
To tighten the caseback by hand, merely maintain the watch in a single hand and the caseback within the different. Align the 2 components and gently press them collectively. You must really feel a slight click on because the caseback snaps into place.
To tighten the caseback utilizing a caseback press, observe these steps:
- Place the watch within the caseback press.
- Align the caseback with the gasket.
- Gently press the caseback into place.
- Tighten the caseback press till the caseback is cosy.
- Take away the watch from the caseback press.
To make sure that the caseback is tightened correctly, you will need to use a torque wrench. A torque wrench is a device that measures the quantity of drive that’s utilized to a screw. This helps to forestall the caseback from being overtightened or undertightened.
The right torque for tightening a Rolex caseback is 5 Nm. Because of this 5 newton-meters of drive needs to be utilized to the caseback.
In case you would not have a torque wrench, you should use a caseback device. A caseback device is a device that helps to tighten and loosen casebacks. Caseback instruments can be found at most jewellery shops and on-line retailers.
To tighten the caseback utilizing a caseback device, observe these steps:
- Place the caseback device on the caseback.
- Gently flip the caseback device till the caseback is cosy.
- Take away the caseback device.
As soon as the caseback is tightened, you will need to verify the gasket. The gasket is a rubber seal that helps to maintain water and mud out of the watch. If the gasket is broken or worn, it needs to be changed.
To verify the gasket, merely have a look at it for any indicators of injury. If the gasket is broken, it needs to be changed with a brand new one.
Strain Testing (for Waterproof Watches)
After getting eliminated the again of your Rolex watch, you will need to strain check it to make sure that it’s nonetheless waterproof. That is particularly necessary in case you plan on taking your watch swimming or diving. To strain check your watch, you have to a strain tester. These might be bought on-line or at most jewellery shops.
To strain check your watch, observe these steps:
- Place your watch within the strain tester.
- Shut the lid of the strain tester and tighten the screws.
- Pump the strain tester till the strain reaches the specified stage (often 3 or 6 atmospheres)
- Wait 1 minute to permit the watch to stabilize.
- Examine the look ahead to any leaks. If there aren’t any leaks, the watch is waterproof.
In case your watch fails the strain check, you will need to have it inspected by a certified watchmaker. They may be capable of determine and repair the leak in order that your watch is as soon as once more waterproof.
Here’s a desk that summarizes the steps for strain testing a Rolex watch:
| Step | Description |
|---|---|
| 1 | Place your watch within the strain tester. |
| 2 | Shut the lid of the strain tester and tighten the screws. |
| 3 | Pump the strain tester till the strain reaches the specified stage (often 3 or 6 atmospheres) |
| 4 | Wait 1 minute to permit the watch to stabilize. |
| 5 | Examine the look ahead to any leaks. If there aren’t any leaks, the watch is waterproof. |
Aftercare and Upkeep
After getting efficiently eliminated the again of your Rolex watch, it is necessary to take correct care of it to make sure its longevity and performance:
1. Clear the Gasket
The gasket is an important element that seals the again of the watch and prevents water from coming into. To keep up its integrity, use a smooth, lint-free fabric to softly wipe away any grime or particles. Keep away from utilizing harsh chemical substances or solvents, as they will injury the gasket.
2. Examine the Seal
Earlier than reattaching the again, fastidiously examine the seal. If there are any cracks, tears, or distortions, the watch will not be waterproof. On this case, it is beneficial to hunt skilled help.
3. Lubricate the Gasket
Making use of a small quantity of silicone grease to the gasket will assist enhance its sealing capabilities and forestall dryness. Use a toothpick or small brush to use the lubricant evenly.
4. Tighten the Again
Use the particular device or your fingers to fastidiously tighten the again of the watch. Keep away from overtightening, as this will injury the case or the again.
5. Strain Take a look at
In case you’re planning to submerge your watch in water, it is sensible to carry out a strain check. This may be carried out by taking your watch to a licensed watchmaker who has the required tools.
6. Retailer Correctly
When not in use, retailer your Rolex watch in a cool, dry place away from direct daylight. This can assist stop tarnishing and injury.
7. Common Servicing
Common upkeep is crucial for preserving your Rolex watch in optimum situation. Each few years, take your watch to a licensed watchmaker for cleansing, lubrication, and changes.
Tips on how to Take away the Again of a Rolex Watch
Rolex watches are identified for his or her sturdiness and precision, however even essentially the most well-made watch will have to be serviced every so often. One of the vital frequent service procedures is eradicating the again of the watch to entry the motion. This is usually a tough job, however it’s doable to do it your self with the precise instruments and data.
Here’s a step-by-step information on how you can take away the again of a Rolex watch:
- Collect your instruments. You will want a case knife, a case opener, and a rubber mallet.
- Place the watch in a vise. Make it possible for the vise is padded to guard the watch from injury.
- Use the case knife to pry open the case again. Watch out to not injury the case or the crystal.
- As soon as the case again is open, use the case opener to take away the motion. Watch out to not contact the motion together with your fingers.
- Examine the motion for any injury. If there may be any injury, you need to take the watch to a certified watchmaker for restore.
- If the motion is in good situation, you may reassemble the watch. Begin by inserting the motion again into the case. Then, use the case opener to screw on the case again.
- Lastly, use the rubber mallet to faucet the case again into place.
Individuals Additionally Ask
How do I do know if my Rolex is actual?
There are a couple of methods to inform in case your Rolex is actual. First, search for the Rolex emblem on the dial, case, and clasp. The emblem needs to be crisp and clear, and the letters needs to be evenly spaced. Second, verify the serial quantity on the case again. The serial quantity ought to match the serial quantity on the guarantee card. Lastly, take the watch to a certified watchmaker for inspection. They may be capable of let you know if the watch is actual or faux.
How a lot does it value to interchange a Rolex crystal?
The price to interchange a Rolex crystal will differ relying on the mannequin of the watch and the kind of crystal. A primary crystal alternative will sometimes value between $100 and $200. A extra complicated crystal alternative, reminiscent of a sapphire crystal, can value as much as $1,000.
How usually ought to I service my Rolex watch?
Rolex watches are designed to be sturdy and exact, however they may have to be serviced every so often. The frequency of service will rely on how usually the watch is worn and the situations through which it’s worn. A common rule of thumb is to have the watch serviced each 5 to 10 years.
